Pimpri-Chinchwad Setback Rules
Pimpri-Chinchwad Municipal Corporation (PCMC) · Pune Metropolitan Region Development Authority (PMRDA)
The PCMC DCPR 2017 is the operative bye-law governing setbacks, building height, and FSI for plots in Pimpri-Chinchwad under PCMC / PMRDA jurisdiction (Category PCMC DCPR 2017 — Pimpri-Chinchwad (Congested + Non-congested)). Front-side margin is driven by abutting road width; side and rear margins for single-family dwellings depend on plot size; for apartments and other uses the side and rear margins scale with building height. Use the calculator below for a quick lookup, or scroll to the full tables.
Front Setback (Road-side Margin)
| Road width | Front setback |
|---|---|
| < 15 m | 3 m |
| ≥ 15 & < 18 m | 3 m |
| ≥ 18 & < 30 m | 4.5 m |
| ≥ 30 m | 4.5 m |
- Pure-residential front margin on a ≥ 30 m road is 4.5 m; the 6.0 m figure applies to residential-with-mixed-use / NH-MDR frontage.
- Congested area front margin: typically 1.5-3.0 m, per gaothan-specific clauses in DCPR 2017.
- For corner plots abutting two or more roads, road-side margin applies on every abutting side.
Side & Rear Setback — Apartments & Other Buildings
| Building height | Rear margin | Side margin | Notes |
|---|---|---|---|
| Any height (side & rear = H/4) | H/4 (min 3 m, max 16 m) | H/4 (min 3 m, max 16 m) | PMC DCPR 2017 Reg 17.2.3(b): side & rear marginal distance = ¼ of building height, minimum 3.0 m (residential), maximum 16.0 m. e.g. 24 m → 6 m, 40 m → 10 m, 64 m+ → 16 m. |
- The marginal distance is a FORMULA (H/4), not fixed steps — it rises continuously with building height, floored at 3.0 m and capped at 16.0 m.
- Congested area allows reductions (min side at ground level ~6.0 m for tall buildings).
- Distance between two buildings on the same plot = the side/rear marginal distance required for the taller building.
- Margins may be reduced for redevelopment under Reg. 7.0 cluster schemes, subject to CFO NOC.
Maximum Building Height
| Road width | Max height | Notes |
|---|---|---|
| < 9.0 m | 15 m | G+4 typical residential |
| 9 - 12 m | 24 m | G+7 — boundary between low- and high-rise |
| 12 - 18 m | 36 m | Mid-rise band |
| 18 - 30 m | 50 m | High-rise — CFO NOC required |
| ≥ 30 m | No limit | No upper cap — subject to AAI clearance, structural review, and FSI limits per zone |
- Building height is also bounded by FSI (zone-based) and slenderness ratio.
- Subject to clearance from the Airport Authority of India for plots near Pune airport approach corridors.
Worked Examples
Key Definitions
Pimpri-Chinchwad Setback & Bye-law Reference Guide
What governs setbacks in Pimpri-Chinchwad?
Building setbacks in Pimpri-Chinchwad are regulated by the Development Control and Promotion Regulations 2017 — Pimpri-Chinchwad Municipal Corporation (PCMC DCPR 2017), notified by the Pune Municipal Corporation · Govt. of Maharashtra on 2017-01-05. The regulation applies across all Category PCMC DCPR 2017 — Pimpri-Chinchwad (Congested + Non-congested) areas — meaning both the Pimpri-Chinchwad Municipal Corporation (PCMC) city limits and the broader Pune Metropolitan Region Development Authority (PMRDA) jurisdiction. Three structural factors determine your minimum setbacks: abutting road width (controls front margin and max height), plot size (controls side/rear for single-family), and building height (controls side/rear for apartments).
Front setback — driven by road width
The front (road-side) margin under PCMC DCPR 2017 starts at 2.5 m for roads up to 9 m wide and scales up to 9.0 m for roads 45 m and wider. For most residential plots in Pimpri-Chinchwad on a typical 30-40 ft (9-12 m) road, the front setback is 2.5 to 3.0 m. Corner plots must observe the road-side margin on every abutting road, which can significantly reduce buildable area on tight plots. Special buildings — high-rises above 25 m, hospitals, hotels, malls, educational institutions — must keep a uniform 12.0 m road-side margin regardless of road width.
Side and rear margins — driven by plot size for residences
For single-family and two-family dwellings (DW1 and DW2 in PCMC DCPR 2017 terminology), side and rear margins are determined by plot area. Tiny plots up to 25 sq.m are exempt (with G+1 cap). Plots between 25 and 150 sq.m need only 1.0-1.5 m on any one side. Once plot size crosses 150 sq.m, a mandatory 2.0 m rear margin kicks in. Plots above 500 sq.m must keep 3.0 m on both sides plus 3.0 m rear. This graduated structure gives smaller, dense urban plots more buildable area while ensuring breathing room in larger plots.
Apartments and commercial — driven by building height
Multi-family, mixed-use, and commercial buildings (anything other than DW1-DW2 and industrial) follow a different logic: the taller the building, the larger the side and rear margins. A low-rise apartment up to 16.5 m needs 3.0 m on every side. Buildings between 16.5 and 25 m need 4.0 m. Buildings between 25 and 45 m need 6.0 m. Anything above 45 m needs 8.0 m. This scaling protects fire access and inter-building daylight as buildings get taller.
Margin between buildings on the same plot
Group housing schemes and multi-block developments must observe an internal margin between buildings as well, separate from plot boundaries. Per Table 6.25, this ranges from 4.5 m for buildings up to 16.5 m, to 12.0 m between buildings of 70 m. Margin from a designated common plot (open recreation area within a layout) is 3.0 m for buildings up to 25 m, and 6.0 m above that. These rules are critical at the master-plan stage; missing them means redesigning blocks late in DA approval.
Coverage of overlays and special zones
The setback tables on this page cover the standard Category PCMC DCPR 2017 — Pimpri-Chinchwad (Congested + Non-congested) rules. Pimpri-Chinchwad additionally has overlay zones with their own special regulations: the Sabarmati Riverfront Development zone, GAMTAL (urbanised village) areas, Core Walled City (heritage), Smart City Node (SPD5), Knowledge Precinct, and Closed Textile Mills Zone (CZ). Plots within these overlays follow the standard setback rules plus the overlay-specific provisions in Sections 7.2-7.6 and 8.1-8.4 of PCMC DCPR 2017. If your plot is in any of these zones, consult the full PCMC DCPR 2017 PDF (download link at the top of this page) before designing.
Frequently asked questions
What is the minimum front setback for a residential plot in Pimpri-Chinchwad?
Per PCMC DCPR 2017 Table 6.24, the minimum road-side margin (front setback) for Category D1 plots in Pimpri-Chinchwad ranges from 2.5 m on roads up to 9 m wide, to 9.0 m on roads of 45 m or more. For a typical 30 ft (≈9 m) wide road, the front setback is 2.5 m; for a 40 ft (≈12 m) road it's 3.0 m; for an 18 m road it jumps to 6.0 m.
What is the side and rear setback for a 200 sq.m plot in Pimpri-Chinchwad?
For a single-family dwelling on a plot between 150 and 300 sq.m, PCMC DCPR 2017 requires a rear margin of 2.0 m and a side margin of 1.5 m on any one side. The other side may abut the boundary. This is per Table 6.26 of the regulation.
What is the maximum building height allowed in Pimpri-Chinchwad?
Maximum building height under PCMC DCPR 2017 is governed by the abutting road width (Table 6.23). On roads less than 9 m wide, height is capped at 10 m (12 m for DW1/DW2 type residential). On 9-12 m roads it goes up to 16.5 m, on 12-18 m roads up to 30 m, and on 18 m and wider roads up to 45 m. In High Density Development Areas (where permitted FSI exceeds 3.5) on 18 m+ roads, height up to 70 m is allowed within 200 m of the road.
Are setback rules different for apartments vs single-family homes in Pimpri-Chinchwad?
Yes. Single-family dwellings (Dwelling 1 and Dwelling 2 in PCMC DCPR 2017) have setbacks driven by plot size (Table 6.26). Apartments and other multi-family or commercial buildings have setbacks driven by building height — 3.0 m for buildings up to 16.5 m, 4.0 m for 16.5-25 m, 6.0 m for 25-45 m, and 8.0 m for buildings above 45 m. Front (road-side) margins follow the same Table 6.24 for both categories.
How do I calculate setbacks for my plot in Pimpri-Chinchwad?
Use three inputs: (1) plot size in square metres, (2) abutting road width in metres, and (3) intended use (single-family, apartment, commercial). The lookup tables on this page give exact values per PCMC DCPR 2017. For corner plots, road-side margin applies on every abutting side. The setback calculator at the top of this page returns front, side, rear, and max height in one click.
Where can I download the official PCMC DCPR 2017 document?
The official Development Control and Promotion Regulations 2017 — Pimpri-Chinchwad Municipal Corporation PDF is published by the Pune Municipal Corporation · Govt. of Maharashtra and hosted on PCMC DCPR 2017 — official Maharashtra regulation. Use the "Download PDF" button at the top of this page for direct access. The regulation is approximately 600 pages; setbacks are covered in Section 6.7 (Margins) and Tables 6.23 through 6.41.
Do these rules apply to plots in AUDA areas outside the AMC limit?
Yes — PCMC DCPR 2017 is a state-level regulation that applies uniformly across Category D1 plots, which covers both AMC (city corporation) and AUDA (urban development authority) jurisdictions. The same Tables 6.24 and 6.26 govern setbacks. Gandhinagar Municipal Corporation (GMC) plots fall under separate tables (6.28 onwards) due to its planned-grid layout. Special zones (Riverfront, Heritage Core, GAMTAL, Smart City Node) have their own overlay rules in addition to base setbacks.
What happens if my plot doesn't meet the minimum setback?
Existing buildings in revenue records before the publication of PCMC DCPR 2017 are typically protected by transitional provisions. New construction or major alteration must comply with current setbacks. For sub-25 sq.m plots, only G+1 construction is permitted with no mandatory setback. For plots affected by road widening, owners can claim FSI compensation against the original boundary (Section 6.3.3) provided the surrendered land is formally transferred. Always consult a licensed architect for plot-specific guidance.
Pimpri-Chinchwad follows its own DCPR 2017 (closely mirroring PMC's, with the H/4 side/rear formula), administered by PCMC; PMRDA governs the surrounding region. Congested-area (gaothan) relaxations apply in the old cores.